Why the Samsung washing machine does not spin the laundry: finding the problem and fixing it
Most washing modes in an automatic machine end with a spin. This removes excess moisture from the laundry and prepares the laundry for further drying.
If the Samsung washing machine does not spin, then this may signal a breakdown, and the need for repair.
Why the Samsung automatic washing machine stopped spinning the laundry, how to determine the breakdown and fix it, we will tell in the article.
Content
Reasons why Samsung washing machine does not spin
The lack of spin can indicate serious failures, without the elimination of which a full cycle of washing things will be impossible.
Breakages that affect spinning:
Lack of draining, in which the washing machine does not go to the next stage of work - spinning.- Worn out motor brushes.
- Stretching the drive belt.
- Damage to the tachometer.
- Failure of the control module.
- Wear of shock absorbers.
- Bearing wear.
- Damage to the electric motor.
- Failure of the pressure switch.
To determine the cause of the malfunction, you must:
- analyze the condition of the machine itself,
- what messages are shown on the display,
- Are abnormal sounds, etc., are emitted during operation
Troubleshooting
The situation with the condition of the washing machine should be analyzed methodically, starting with the simplest options, checking each node step by step.
Consumer errors
Not in all cases, the lack of spinning indicates a breakdown. First, you need to assess the situation and pay attention to possible consumer mistakes.
Situations in which the problem is not spinning:
Drum overload. Too many things have been laid, which, having absorbed water, have become even heavier. The machine is unable to rev up and spin out the laundry. Putting some of the laundry out of the drum will help resolve the issue.- Another situation in which the spinning of things is not performed is the choice of one of the delicate modes. Or accidental, or maybe special, disabling this function.
- Imbalance of things in the drum.This situation can arise when things are gathered in one lump during washing, and the machine cannot distribute them evenly by itself. For example, a stray blanket or duvet cover, inside which all other things from the drum got inside.
- The mode of reduced speed during spinning is selected (or without spinning at all). If it is possible to set different spin intensities, then the minimum can be randomly selected.
When starting the washing machine, make sure that the program is set correctly and that the total weight of items in the drum does not exceed the permissible value.
Determining the source of failure
In rare cases, an accidental failure can affect the operation of the washing machine.... Such factors include a voltage drop in the network or a problem with the water supply. When the operation of external communications stabilizes, it is necessary to repeat the start of the spin function and monitor the operation of the washing machine.
In some cases, the washing stops, and the washing machine itself reports a failure by issuing an alphanumeric error code on the display. This could be:
- E4,
- UB,
- UE.
At first glance, it is almost impossible to determine what the problem is, so it is necessary to carry out the analysis gradually - from node to node.
In some cases, you can find out about the type of breakdown by the condition of the machine:
| "Behavior" of the washing machine | Which node should you pay attention to |
| The lack of a set of revolutions on the spin | Drive belt |
| The drum is not spinning at all or is not gaining momentum | Tachometer, control module |
| No draining - the cycle does not reach spin | Pump, branch pipe, filter, drain hose, sewerage, control module |
| No spinning on spin, sparking | Motor brushes |
| Excessive vibration when trying to spin the drum, spinning is not performed. There may also be an uncharacteristic pounding of the drum on the body | Shock absorbers |
| When trying to spin, the machine makes loud noises and rattles. If you swing the empty drum by hand, it dangles freely on the shaft. In addition, there may be rusty streaks on the outside of the tank. | Bearings |
| "Hanging" on spin. If you repeat the start, the drum does not move. The hum of the motor may be heard. It is also possible to knock out plugs or, conversely, a complete failure of work. | Electric motor |
| The drum rotates during spinning, but there is no spin as such | Pressostat |
Even in spite of the characteristic signs inherent in a particular breakdown, a deep professional diagnosis of the device may be required.
What to do?
If consumer errors are excluded, you can proceed to the analysis of the nodes. It is better to do it in the following sequence: start with the most accessible, leaving the most difficult for later.
Preliminary preparation of the machine:
- if there is water in the washing machine, it must be drained (naturally or through an emergency drain);
- disconnect the washing machine from the mains;
- shut off the water supply to the device;
- pull out the washing machine in such a way as to provide easy access to its back wall;
- pull out the powder receptacle.
Violation of the drain
If the washing machine does not drain the water, then it cannot go to spinning. In this case, it is necessary to gradually sort out all possible problems associated with the drain.
Next, you need to diagnose the operation of the drain pump, check the patency of all water drainage systems.
The drive belt has worn out
If the drive belt is stretched, it will not provide adequate contact with surfaces. When it "slips", the part needs to be replaced, since it cannot be repaired.
Damage to the tachometer
A tachometer is an element of a washing machine that is involved in the process of drum rotation. This node is responsible for controlling the number of revolutions of the engine..
If it breaks, the washing machine does not rotate the drum intensively. As a result, spinning is either not performed or performed very poorly.
A tachometer is a fairly reliable element that rarely breaks.
Fault in the control unit
The control unit is a board that connects to the buttons and sensors on the front paneland also transmits signals to the units of the washing machine. It is located in the upper part of the front side of the washing machine.
Diagnostics of a malfunction is a complex process that requires special knowledge and tools (soldering iron, multimeter, etc.).
Motor brushes wear
In the process of rotation of the drum during spinning, the engine is activated. In cases where it sparks and does not generate the required torque, it is necessary to inspect the condition of the motor brushes... If they do not fit well with the collector due to wear, the master will change them.
Shock absorbers worn out
Shock absorbers in the washing machine are needed to damp the vibrations of the drum during washing and spinning. When the shock absorbers wear out, vibrations are not absorbed, while electronic sensors prevent the drum from spinning.
As a result, spinning is not performed. With such a breakdown, replacement of shock absorbers is required.
When the shock absorbers are worn out, both must be replaced at once., even if the degree of damage in one of them is minor.
The video will tell you about replacing the shock absorbers of the washing machine:
Bearing failure
Bearing wear can occur with prolonged use of the washing machine. During this time, the oil seal begins to lose its tightness, due to which water gets into the bearings. This will wash away the grease and lead to rusting, and vibration and rotation further aggravate the situation.
Damage to the motor
If the washing machine is unable to spin, the likelihood of such a serious breakdown as the combustion of an electric motor must not be overlooked... Malfunctions in this unit can be caused by a short circuit, stator breakdown and other circumstances.
The pressure switch has broken
The pressure switch is a sensor that monitors the water level... The signal from it about the water level goes to the control module.
With a normal signal, which corresponds to the actual liquid level, the control module, after draining, gives a signal for spinning.
But if the pressostat gives wrong signals, the control module does not "give the go-ahead" to spin. Such a situation may occur when the pressure switch hangs on a signal indicating that the tank is full of water. Even if in fact all the liquid has been drained, the control module does not receive information about this.
The master diagnoses the pressure switch - checks for blockage, damage... After restoring the functionality of this unit, the washing machine will start spinning.
How to check the pressure switch in the washing machine, the video will tell you:
Master's challenge: how to find and how much to pay?
Sometimes you can even cope with the problem in the absence of spinning on your own, but it is better to entrust the performance of high-quality diagnostics and repair of units to a professional. To do this, contact a company that provides services for the repair of household appliances., and Samsung washing machines in particular.
The cost of repairs consists of the prices for the work of the master, the price of parts requiring replacement, and consumables. Depending on the complexity of the breakdown, the repair price increases.There may also be a difference in the prices of companies.
The average price for repairs in the capital (excluding the price of parts) is:
diagnostics of the pressure switch, repair, replacement - from 1 600 rubles;- replacement of shock absorbers - from 2,200 rubles;
- repair / replacement of an electric motor - from 2,000 rubles;
- replacement of bearings - from 3 300 rubles;
- replacement of a tachometer - from 2,200 rubles;
- drain cleaning - from 1 100 rubles;
- replacement of motor brushes - from 1,400 rubles;
- replacement of the drive belt - from 900 rubles, etc.
The final cost is determined on a case-by-case basis.
You can find a repair company for Samsung washing machines on the Internet. For devices that are still under warranty, you need to contact the service center with the problem... Information about them is indicated in the documents for the washing machine.
The master is called directly by phone. The dispatcher needs to describe the breakdown of the washing machine and name the model (it is indicated in the passport for the device).
Expert advice
Recommendations of the mastersrepairing washing household appliances will help to avoid problems with the spin function in the washing machine:
- Do not overload the washing machine. This will allow the engine to remain functional and prevent overloading.
When washing, you do not need to add more washing powder than recommended. Abundant foam due to its excess can disable the water level sensor.- Before putting it into the drum, it is important to check the contents of the pockets and not put things in it that require repair - with poorly sewn buttons, worn ones, etc. Small objects are the main cause of not only blockages, but also breakdowns.
- Do not use the spin function when washing shoes, as this puts an overload on many components and can lead to equipment damage.
- Ensuring a stable voltage in the electrical network will prevent burnout and failure of the elements of the washing machine.
Find out more about repairing Samsung washing machines - in this section.
Related videos
Why the Samsung washing machine does not spin and what to do with it, the video will tell you:
Conclusion
If the Samsung washing machine does not spin, the problem may be both in the user's improper actions and in equipment failure. It is quite possible to fix some violations on your own, but for most of the failures, repair carried out by a master will be needed.
Loading...
